raebyrn

Hi all,

I can receive external calls, but always get the "all circuits are busy now" announcement when trying to call an outside number. If tried following the OpenVox Elastix guide to the letter. The hardware detection in Elastix has always given me this result:

Port 1: TE-mode BRI S/T interface line (for phone lines)
-> Protocol: DSS1 (Euro ISDN)
-> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib.
-> childcnt: 2
* Port NOT useable for PBX (maybe there is already a PBX running?)
--------

*CLI> misdn show channels
Channel List: (nil)

Is this the problem?

What .conf files should I attach?

Thanks and best regards,

Rae

P.S. here's the log of such a call attempt

    -- Goto (macro-dialout-trunk,s,21)
    -- Executing [s@macro-dialout-trunk:21] Set("SIP/1076-00000001", "pre_num=AMP:mISDN /g:isdn/") in new stack
    -- Executing [s@macro-dialout-trunk:22] Set("SIP/1076-00000001", "the_num=OUTNUM") in new stack
    -- Executing [s@macro-dialout-trunk:23] Set("SIP/1076-00000001", "post_num=") in new stack
    -- Executing [s@macro-dialout-trunk:24] GotoIf("SIP/1076-00000001", "1?outnum:skipoutnum") in new stack
    -- Goto (macro-dialout-trunk,s,25)
    -- Executing [s@macro-dialout-trunk:25] Set("SIP/1076-00000001", "the_num=01753036831") in new stack
    -- Executing [s@macro-dialout-trunk:26] Dial("SIP/1076-00000001", "mISDN /g:isdn/01753036831|300|") in new stack
  == Everyone is busy/congested at this time (1:0/0/1)
    -- Executing [s@macro-dialout-trunk:27] Goto("SIP/1076-00000001", "s-CHANUNAVAIL|1") in new stack
    -- Goto (macro-dialout-trunk,s-CHANUNAVAIL,1)
    -- Executing [s-CHANUNAVAIL@macro-dialout-trunk:1] GotoIf("SIP/1076-00000001", "1?noreport") in new stack
    -- Goto (macro-dialout-trunk,s-CHANUNAVAIL,3)
    -- Executing [s-CHANUNAVAIL@macro-dialout-trunk:3] NoOp("SIP/1076-00000001", "TRUNK Dial failed due to CHANUNAVAIL (hangupcause: 66) - failing through to other trunks") in new stack
    -- Executing [01753036831@from-internal:5] Macro("SIP/1076-00000001", "outisbusy|") in new stack
    -- Executing [s@macro-outisbusy:1] Playback("SIP/1076-00000001", "all-circuits-busy-now|noanswer") in new stack
    -- <SIP/1076-00000001> Playing 'all-circuits-busy-now' (language 'en')
    -- Executing [s@macro-outisbusy:2] Playback("SIP/1076-00000001", "pls-try-call-later|noanswer") in new stack
    -- <SIP/1076-00000001> Playing 'pls-try-call-later' (language 'en')
  == Spawn extension (macro-outisbusy, s, 2) exited non-zero on 'SIP/1076-00000001' in macro 'outisbusy'
  == Spawn extension (from-internal, 01753036831, 5) exited non-zero on 'SIP/1076-00000001'
    -- Executing [h@from-internal:1] Macro("SIP/1076-00000001", "hangupcall") in new stack
    -- Executing [s@macro-hangupcall:1] GotoIf("SIP/1076-00000001", "1?skiprg") in new stack
    -- Goto (macro-hangupcall,s,4)
    -- Executing [s@macro-hangupcall:4] GotoIf("SIP/1076-00000001", "1?skipblkvm") in new stack
    -- Goto (macro-hangupcall,s,7)
    -- Executing [s@macro-hangupcall:7] GotoIf("SIP/1076-00000001", "1?theend") in new stack
    -- Goto (macro-hangupcall,s,9)
    -- Executing [s@macro-hangupcall:9] Hangup("SIP/1076-00000001", "") in new stack
  == Spawn extension (macro-hangupcall, s, 9) exited non-zero on 'SIP/1076-00000001' in macro 'hangupcall'
  == Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/1076-00000001'

[ Last edited by raebyrn at 2010-7-29 16:46 ]

Denins.Den

Please show  /etc/mISDN.conf and /etc/asterisk/misdn.conf

raebyrn

Hi Denis,

thanks for the quick response. The problem was in the trunk. I copied "mISDN /g:isdn/$OUTNUM$" from the OpenVox Elastix guide. When I changed this to "mISDN/g:isdn/$OUTNUM$" outgoing calls worked.

Best regards,

Rae